configuration_sim_telarray

LSTN-01

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	300	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

LSTN-02

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	300	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

LSTN-03

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	300	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

LSTN-04

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	300	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

LSTS-01

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	300	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

LSTS-02

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	300	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

LSTS-03

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	300	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

LSTS-04

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	300	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-01

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-02

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-03

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-04

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-05

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-06

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-07

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-08

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-09

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-10

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-100

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-101

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-103

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-104

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-105

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-11

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-113

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-114

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-115

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-12

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-13

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-14

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-15

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-201

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-202

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTN-207

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-01

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-02

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-03

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-04

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-05

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-06

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-07

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-08

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-09

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-10

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-11

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-115

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-116

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-117

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-118

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-119

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-12

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-120

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-121

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-122

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-123

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-124

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-125

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-126

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-127

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-128

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-129

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-13

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-130

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-131

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-132

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-133

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-14

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-301

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-302

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-304

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-306

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-308

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-310

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-312

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTS-314

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTx-FlashCam

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
min photons	1.0.0	360	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
store photoelectrons	1.0.0	22	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.
tailcut scale	1.0.0	2.6	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

MSTx-NectarCam

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photoelectrons	1.0.0	30	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
min photons	1.0.0	450	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
store photoelectrons	1.0.0	26	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.
tailcut scale	1.0.0	2.3	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-01

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-02

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-03

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-04

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-05

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-06

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-07

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-08

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-09

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-10

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-11

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-115

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-116

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-117

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-118

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-119

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-12

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-120

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-121

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-122

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-123

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-124

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-125

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-126

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-127

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-128

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-129

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-13

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-130

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-131

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-132

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-133

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SCTS-14

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	25	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	600	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	20	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-01

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-02

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-03

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-04

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-05

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-06

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-07

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-08

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-09

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-10

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-11

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-12

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-13

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-14

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-15

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-16

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-17

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-18

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-19

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-20

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-21

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-22

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-23

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-24

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-25

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-26

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-27

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-28

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-29

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-30

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-31

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-32

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-33

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-34

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-35

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-36

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-37

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-38

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-39

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-40

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-41

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-42

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-43

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-44

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-45

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-46

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-47

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-48

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-49

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.

SSTS-50

Parameter Name	Parameter Version	Values	Short Description
correct nsb spectrum to telescope altitude	1.0.0	atm_trans_2200_1_3_0_0_0.dat	Correct the night-sky background spectrum to the telescope altitude from the altitude where the Benn & Ellison spectrum was measured. The correction is done within sim_telarray and is based on the atmospheric transmission to 2200 m a.s.l (atm_trans_2200_1_3_0_0_0.dat).
iobuf maximum	1.0.0	1000000000 byte	Buffer limits for input and output of eventio data.
iobuf output maximum	1.0.0	400000000 byte	The maximum size of the I/O buffer for output data, including raw data for all telescopes.
min photoelectrons	1.0.0	12	Minimum number of detected photoelectrons required before running electronics simulation.
min photons	1.0.0	250	Minimum number of photons required before doing simulation.
random generator	1.0.0	mt19937	Random generator used.
sampled output	1.0.0	True	Select a specific output format (if several available). A value of 0 means to write ADC sums, a value of 1 to write ADC samples.
save_pe with amplitude	1.0.0	True	True if photo-electron data is to be stored with the resulting amplitudes (in mean-p.e. units) in addition to the arrival times. Storing of photo-electron data should be activated separately (see save_photons (bit 1) and store_photoelectrons parameters) but non-zero values of this parameter will also activate save_photons bit 1. Storing p.e. in internal calibration events is controlled separately by save_calibration_pe.
store photoelectrons	1.0.0	10	While the save_photons=2 configuration option will save photo-electron data for all events, this parameter allows to set a lower limit on the number of photo-electrons which must get registered before deciding to store them. Setting it to a value of zero or bigger (default: -1) will automatically enable the corresponding save_photons bit. It should be cross-checked that the min_photons parameter is unlikely to result in fewer than the given number of photo- electrons, as no attempt is made to trace photons through the telescope and produce any photo-electrons if there are too few photons in the first place.
tailcut scale	1.0.0	1	The special scheme for selecting pixels belonging to a shower image as implemented in sim_telarray (as opposed to the traditional two-level tailcut scheme) has multiple thresholds for the various levels of confidence that a pixel actually belongs to the shower image. Instead of making them individually configurable, a common scale factor can be applied to all of them.